1. Hello Guest. You have limited privileges and you can't "SEARCH" the forums. Please "Log In" or "Sign Up" for additional functionality. Click HERE to proceed.

Hard to find neutral after rebuild

Discussion in 'XJ Technical Chat' started by Thrasher, Feb 15, 2018.

  1. Thrasher

    Thrasher Member

    Messages:
    402
    Likes Received:
    24
    Trophy Points:
    18
    Location:
    Oak Ridge, Tennessee
    What transmission components are likely to be bad? It is hard to find neutral after rebuild on a FJ600?
     
    Thrasher, Feb 15, 2018
    #1
  2. cgutz

    cgutz Well-Known Member

    Messages:
    1,203
    Likes Received:
    719
    Trophy Points:
    113
    Location:
    SE South Dakota
    Fine tuning the clutch cable helps make it easier to find neutral on my XJ.
     
    cgutz, Feb 15, 2018
    #2
    k-moe and Toomanybikes like this.
  3. Toomanybikes

    Toomanybikes Well-Known Member

    Messages:
    2,835
    Likes Received:
    814
    Trophy Points:
    113
    Location:
    Tsawwassen bc
    Will it shift properly when it's not running? And warped clutch plates will do that also
     
    Toomanybikes, Feb 15, 2018
    #3
    k-moe likes this.
  4. Jetfixer

    Jetfixer Well-Known Member

    Messages:
    3,179
    Likes Received:
    1,489
    Trophy Points:
    113
    Location:
    Nothern Indiana
    Shift linkage at shift lever may need tweeked.
     
    Jetfixer, Feb 16, 2018
    #4
  5. Thrasher

    Thrasher Member

    Messages:
    402
    Likes Received:
    24
    Trophy Points:
    18
    Location:
    Oak Ridge, Tennessee
    No linkage. I think it is shifting forks.
     
    Thrasher, Feb 16, 2018
    #5
  6. Chitwood

    Chitwood Well-Known Member

    Messages:
    866
    Likes Received:
    374
    Trophy Points:
    63
    Location:
    Fort Atkinson, Wisconsin
    Like Kmoe always says, pick the low hanging fruit first. I would suggest exhausting all possibilities externally before opening it up if it's necessary
     
    Chitwood, Feb 16, 2018
    #6
  7. k-moe

    k-moe Pie, Bacon, Bourbon. Moderator Premium Member

    Messages:
    19,613
    Likes Received:
    6,707
    Trophy Points:
    113
    Location:
    The City of Seven Hills
    The adjustable linkage (if present on your model, I don't recall if the FJ has one) is external, between the pedal and the shift shaft. The #1 cause for a difficult to find neutral is an improperly adjusted clutch cable. Rickcomatic has an excellent write up on the process for an XJ, which is applicable to the FJ.
    http://www.xjbikes.com/forums/bookmarks/153/view-item

    If there were any internal defects, they would show up while shifting into, or out of, one or more gears.
    Yamaha transmissions of the era are very finicky when it comes to finding neutral; it's very easy to shift right through it and never notice the detent. some people find it easier to shift down from second to reach neutral.
     
    k-moe, Feb 16, 2018
    #7
  8. Polock

    Polock Well-Known Member

    Messages:
    9,751
    Likes Received:
    2,093
    Trophy Points:
    113
    Location:
    Beaver Falls, PA
    same kind of oil as before ?
     
    Polock, Feb 16, 2018
    #8
  9. Thrasher

    Thrasher Member

    Messages:
    402
    Likes Received:
    24
    Trophy Points:
    18
    Location:
    Oak Ridge, Tennessee
    It is set up with GP shift, same oil, cable is fine, clutch plates are flat.
     
    Thrasher, Feb 16, 2018
    #9

Share This Page