I don't mean to sound dumb but what do mean when you say ohm out the components and diode check not really competent with electricity and a...
OK at the moment am in the middle of cleaning out the fuel tank I'll put it back on add some fuel and see if it fires. But for the time being am I...
Hi I did as you suggested and completely removed the black and white wire and it sparks now on all 4 pots. At the moment I have the clutch switch...
OK so I can completely disconnect this wire and leave it out the block? We're does it run back to and is the neutral switch causing the fault as I...
Having a problem trying to get a spark on my Fj600 85. The bike cranks but can't get a spark on any of the plugs. I read about the black and white...
Yeah seen a kit on ebay for 23 quid so might get that it's the 4 brush type as well. Didn't know the later models were only 2 brushes though. Not...
Just noticed as well some crafty bastard has put in a a brush holder of a seca by the looks of it. All Fj600 and xj600 have 4 brush holders as...
Also the bolt that goes through the hole in the starter has like a kind of collar it goes through so u can tighten a nut down to it is missing. On...
Hi stu OK this what I've got so far, removed starter and with a known good battery ran jumper leads to it, it span at first really slowly then...
Hi used lithium grease hoped this was a good insulator.
:):) much appreciated
All cables were greased the one coming out the back of the crankcase bolt number 32 I believe that runs up to the negative terminal and underneath...
Yeah I replaced the larger of the two relays the smaller one I haven't. Tested side stand switch and it appears to work but when you press starter...
Hi stu Turn ignition and power across all fuses power at the starter relay and red and white wire. Yes tried bridging relay with a flat screw...
Man am stumped got everything working on the bike lights horn etc, all switches work but no spark ran a test light over the coils and no power to...
I think possibly they might off spliced the green wire with the blue wire running off it and attached it to one of the headlight wires. So that...
OK so picked up my relay and attempting to wire up the front of the bike so far I've got: Headlight: green,black, yellow Horn: pink and brown...
Wiring the bike back up and I think I blew the relay or at least earthed it. Have power all over the bike as have been using a test light and...
Hi Yeah but there of the later model, need the 9 pin plug off the earlier model. Cmsnl have them or something that looks similar but there...
Looking for a flasher relay for the above bike anyone know were u can get an after market one like this. Checked online obviously but cant see...
Just fiited a new pair of ignition coils to my xj coming off the loom I have 2 red and white wires and 2 other wires one orange and I think the...
Hi read your previous post from a few years back on the cylinder head torque settings you were trying to confirm. My Haynes manual states like you...
OK so attempting my head rebuild again the Haynes manual states 22nm for the cylinder head nuts. Seems kind of light to me is this correct anyone?...
Problems with the gear box assembly basically the shift shaft t assembly lever keeps popping out from behind the selector drum. It looks like I've...
So would I need the radian/fz 600carbs as well from an earlier radian/fz600 engine and or different carb to head rubbers.
Am having some trouble putting an 84 Xj600 engine back together. I was wondering could I just put an earlier radian 600 into an Xj600 84 frame or...
[ATTACH] [ATTACH] [ATTACH] Hi mate yeah I have the selector pin correct and have the change lever spring positioned on either side of the guide...
I think am getting stuck on the travel section of the drum. It could possibly be its at the end of its travel not the beginning possibly. But how...
[ATTACH] [ATTACH] [ATTACH] [ATTACH] Got my engine back together recently and realised that I couldn't engage neutral and place the bike in gear....
OK thank you much appreciated.
The frame was powder coated recently the bars are just stock ones which are unpainted.
I've recently rebuilt an 84 xj600 engine, it's the earlier model with different pick ups and alternator moved to the end of the stater clutch...
Hi yes it's an 89 per diversion 600 engine part of the lower crank case is snapped so wouldn't keep compression anyway planned on stripping it...
Hi I have a 89 fj600 and dropped the engine from the bike as it was seized. I have an older empty 85 fj 600 crankcase and was planning to...
hi jacob if u manage to come across a front mudguard/fender for a 1989 xj600 pre diversion in white. tell me the price and i will forward it to...
