1. Some members were not receiving emails sent from XJbikes.com. For example: "Forgot your password?" function to reset your password would not send email to some members. I believe this has been resolved now. Please use "Contact Us" form (see page footer link) if you still have email issues. SnoSheriff

    Hello Guest. You have limited privileges and you can't "SEARCH" the forums. Please "Log In" or "Sign Up" for additional functionality. Click HERE to proceed.

Bike "jumps" when shifting from neutral to first

Discussion in 'XJ Technical Chat' started by prock, May 5, 2009.

  1. prock

    prock Member

    Messages:
    91
    Likes Received:
    0
    Trophy Points:
    6
    Location:
    Guelph, Ontario
    Hi. When I put my 83 maxim 750 into 1st while standing the bike tries to "jump" forward a bit even with the clutch fully depressed. Is this an issue?
     
  2. Robert

    Robert Active Member

    Messages:
    7,479
    Likes Received:
    9
    Trophy Points:
    38
    Location:
    Ventura CA
    It could be that your clutch is miss adjusted (very common issue), but a fair amount of clunk in that particular shift is normal.
     
  3. SaltyCITYXJ550

    SaltyCITYXJ550 Member

    Messages:
    95
    Likes Received:
    0
    Trophy Points:
    6
    Location:
    Salt Lake City, UT
    It may just be a clutch adjustment, or it may be severly worn clutch clutch plates. Try adjusting the cable first and see if that helps. If not you may be looking at a new clutch.
     
  4. SLKid

    SLKid Active Member

    Messages:
    1,471
    Likes Received:
    0
    Trophy Points:
    36
    Location:
    Troy, Va (Charlottesville)
    I have the same problem. Only to first though. It only does it going into second on up if she's not completely warm.
    So how do you adjust the clutch cable? Its not like the throttle cable
    -SLKid
     
  5. SaltyCITYXJ550

    SaltyCITYXJ550 Member

    Messages:
    95
    Likes Received:
    0
    Trophy Points:
    6
    Location:
    Salt Lake City, UT
    There is a series of nuts on a threaded end down where it connects the arm by your right foot.
     
  6. bigfitz52

    bigfitz52 Well-Known Member Premium Member

    Messages:
    21,283
    Likes Received:
    418
    Trophy Points:
    83
    Location:
    Rural SE Michigan 60 miles N of Motown
    There should also be an adjuster at the handlebar end.

    The "clunk" going into gear is caused by clutch drag. Even a perfectly adjusted clutch will produce some drag, resulting in the "clunk" especially when cold. An EXTREME "clunk" or a persistent one does indicate the clutch is dragging and needs adjusting.

    Worn plates won't cause drag; they'll cause slippage.
     
  7. SQLGuy

    SQLGuy Well-Known Member

    Messages:
    2,140
    Likes Received:
    175
    Trophy Points:
    63
    Location:
    Colorado Springs, Colorado USA
    If your idle is too high, you'll also see this behavior.
     
  8. JoeFriday77

    JoeFriday77 Member

    Messages:
    604
    Likes Received:
    1
    Trophy Points:
    18
    Location:
    North Texas
    There was a post on here about clutch adjustment. I can't remember who posted it. I followed it to a T and it worked like a charm.
     
  9. RickCoMatic

    RickCoMatic Well-Known Member

    Messages:
    13,843
    Likes Received:
    66
    Trophy Points:
    48
    Location:
    Massachusetts, Billerica
    Search: Clutch Cable Replacement and Adjustment.
     

Share This Page