1. Some members were not receiving emails sent from XJbikes.com. For example: "Forgot your password?" function to reset your password would not send email to some members. I believe this has been resolved now. Please use "Contact Us" form (see page footer link) if you still have email issues. SnoSheriff

    Hello Guest. You have limited privileges and you can't "SEARCH" the forums. Please "Log In" or "Sign Up" for additional functionality. Click HERE to proceed.

82 Seca 650 (non-turbo) ... intermittent starter issues

Discussion in 'XJ Technical Chat' started by ttumr2, Jul 8, 2012.

  1. ttumr2

    ttumr2 New Member

    Messages:
    13
    Likes Received:
    0
    Trophy Points:
    1
    Edit
     
  2. trickedout420

    trickedout420 Member

    Messages:
    90
    Likes Received:
    0
    Trophy Points:
    6
    Location:
    Greenwood MO
    well alot of the time it turns out to be the oil your running...these motors dont like synthetic oils.

    what kind of oil are you running
     
  3. ttumr2

    ttumr2 New Member

    Messages:
    13
    Likes Received:
    0
    Trophy Points:
    1
    Plain old Yamaha 10W-30. Also might mention that it starts fine after it has run within the past 24 hours.
     
  4. MiGhost

    MiGhost Well-Known Member

    Messages:
    1,576
    Likes Received:
    160
    Trophy Points:
    63
    Location:
    Lower 48 in general. Otherwise Central Mitten.
    If you are getting starter engagement the suddenly the starter seems to spin loose. That would be an indication of the starter clutch going bad.

    If the starter just seems to drag on slowly. That would be an indication that the brushes are getting worn, and it is time to rebuild the starter. Worn starter brushes will draw to much current, and not allow enough power for the TCI to fire the coils.

    Ghost
     
  5. ttumr2

    ttumr2 New Member

    Messages:
    13
    Likes Received:
    0
    Trophy Points:
    1
    It never spins loose, but sounds about the same the whole time the button is pushed down. So, will def go ahead and do the starter brushes. Hoping it's not too hairy of a job.

    Thanks for your help!
     
  6. ttumr2

    ttumr2 New Member

    Messages:
    13
    Likes Received:
    0
    Trophy Points:
    1
    Also changing spark plugs and cleaning electrical contacts with contact cleaner. Can't hurt.
     
  7. MiGhost

    MiGhost Well-Known Member

    Messages:
    1,576
    Likes Received:
    160
    Trophy Points:
    63
    Location:
    Lower 48 in general. Otherwise Central Mitten.
    Also go through the entire wiring harness (including the rats nest in the headlight bucket) to make sure everthing is clean, and tight.

    Ghost
     
  8. KrS14

    KrS14 Active Member

    Messages:
    1,642
    Likes Received:
    9
    Trophy Points:
    38
    Location:
    St Marys, Ontario
    Just as a side note: 10W-30 is way too light an oil for 100 degree riding. You should be using 20W-50.
     
  9. ttumr2

    ttumr2 New Member

    Messages:
    13
    Likes Received:
    0
    Trophy Points:
    1
    edit
     
  10. ttumr2

    ttumr2 New Member

    Messages:
    13
    Likes Received:
    0
    Trophy Points:
    1
    And thanks for the oil advice. Just checked and I'm actually running 10W-40. Memory failed me. But will def consider switching to 20W-50 since it's usually pretty warm here. The bike came from the northeast, so they always ran 10W-40.
     
  11. ttumr2

    ttumr2 New Member

    Messages:
    13
    Likes Received:
    0
    Trophy Points:
    1

Share This Page