1. Some members were not receiving emails sent from XJbikes.com. For example: "Forgot your password?" function to reset your password would not send email to some members. I believe this has been resolved now. Please use "Contact Us" form (see page footer link) if you still have email issues. SnoSheriff

    Hello Guest. You have limited privileges and you can't "SEARCH" the forums. Please "Log In" or "Sign Up" for additional functionality. Click HERE to proceed.

FJ600 - Broken Piece Under Chain Cover

Discussion in 'XJ Technical Chat' started by mreinsmith, Feb 6, 2013.

  1. mreinsmith

    mreinsmith New Member

    Messages:
    26
    Likes Received:
    0
    Trophy Points:
    1
    Location:
    Southeast, PA
    When we removed the chain cover we found a broken plastic piece inside.

    We can't figure out what it is from any of the parts explosions in the manual.

    It appears that it was circular and possibly had a small spring in it

    Pictures are below

    TIA

    M

    [​IMG]

    [​IMG]
     
  2. bigfitz52

    bigfitz52 Well-Known Member Premium Member

    Messages:
    21,283
    Likes Received:
    418
    Trophy Points:
    83
    Location:
    Rural SE Michigan 60 miles N of Motown
  3. mreinsmith

    mreinsmith New Member

    Messages:
    26
    Likes Received:
    0
    Trophy Points:
    1
    Location:
    Southeast, PA
    the neutral switch seems to be intact.

    I've been looking at the parts diagrams, Intparticular the diagram for "crankcase cover" and "Electrical 2" and I still can't figure out what the heck it is.

    any other ideas?

    M
     
  4. lostboy

    lostboy Well-Known Member

    Messages:
    1,225
    Likes Received:
    324
    Trophy Points:
    83
    Location:
    Tillsonburg, Ontario, Canada
    It looks to me that the chain is hitting the plastic sleeve around the shifter shaft. Adjust the chain.
     
  5. bigfitz52

    bigfitz52 Well-Known Member Premium Member

    Messages:
    21,283
    Likes Received:
    418
    Trophy Points:
    83
    Location:
    Rural SE Michigan 60 miles N of Motown
    There is one off-hand possibility; and that's maybe it's not from behind that cover at all.

    Oil seals have springs in them. Did your sprocket-carrier oil seal self destruct, and the pieces go for a ride on the chain only to get caught there?

    This one?

    [​IMG]
     
  6. mreinsmith

    mreinsmith New Member

    Messages:
    26
    Likes Received:
    0
    Trophy Points:
    1
    Location:
    Southeast, PA
    I'll check that out

    Thanks

    M
     
  7. mreinsmith

    mreinsmith New Member

    Messages:
    26
    Likes Received:
    0
    Trophy Points:
    1
    Location:
    Southeast, PA
    That DOES look like a seal spring!

    I'll check that out too

    M
     
  8. mreinsmith

    mreinsmith New Member

    Messages:
    26
    Likes Received:
    0
    Trophy Points:
    1
    Location:
    Southeast, PA
    Sure enough, the grease seal is missing from the that side of the wheel!

    So that begs the question, do you think I should replace the bearing as well?
     
  9. Polock

    Polock Well-Known Member

    Messages:
    9,751
    Likes Received:
    2,097
    Trophy Points:
    113
    Location:
    Beaver Falls, PA
    what holds that counter shaft bearing in? looks like there's a snap ring groove without a snap ring in it
     
  10. bigfitz52

    bigfitz52 Well-Known Member Premium Member

    Messages:
    21,283
    Likes Received:
    418
    Trophy Points:
    83
    Location:
    Rural SE Michigan 60 miles N of Motown
    You should replace them all. That picture is from my "how-to" on replacing rear wheel bearings, done on my chain-driven 550 Seca: http://xjbikes.com/Forums/viewtopic/t=35134.html Have at it! I covered both the old school hammer and punch method, plus the use of bearing extractors. If you use fully sealed bearings, that seal becomes redundant; but I'd install it anyway.

    Ask questions if you have any. And check that chain and sprockets; if you're not familiar with the correct way to check a sprocket for wear say so and I'll happily hook you up.

    (I love getting long-distance diagoses right, BTW. 8) )
     

Share This Page