1. Some members were not receiving emails sent from XJbikes.com. For example: "Forgot your password?" function to reset your password would not send email to some members. I believe this has been resolved now. Please use "Contact Us" form (see page footer link) if you still have email issues. SnoSheriff

    Hello Guest. You have limited privileges and you can't "SEARCH" the forums. Please "Log In" or "Sign Up" for additional functionality. Click HERE to proceed.

What did you do to your Yamaha today?

Discussion in 'XJ Technical Chat' started by Cutlass84, Jun 4, 2007.

  1. Fuller56

    Fuller56 Well-Known Member

    Messages:
    1,116
    Likes Received:
    547
    Trophy Points:
    113
    Location:
    Cary, NC (winter) Harpursville, NY (summer)
    Are there any paintless dent repair guys in your area? Those guys do some amazing work pretty quickly too. They should be able to work that dent out pretty easy, at least to my inexperienced eye. One in the Cary, NC area un-hail damaged my GMC Canyon pick up in a day.
    As far as the rust, WalMart has 30% vinegar in the auto/RV parts area. Grocery store vinegar is, I think, 3%. I have had excellent luck with electrolysis as well. Good Luck!
     
  2. Rayzerman

    Rayzerman Member

    Messages:
    70
    Likes Received:
    31
    Trophy Points:
    18
    Location:
    Ontario Canada
    I use Evaporust to clean tanks with light/medium rust. Water soluable, can reuse if not black (filter it).

    I pulled 3 baseball sized dents out of a tank using a cheap Chinese dent pulling system where you glue on buttons with hot melt then use the provided tool to work them out (start at the edges and work your way in, pull in slow movements). Eventually, you'll have to sand, use filler, prime and paint/clearcoat.
     
  3. ScottFree

    ScottFree Active Member

    Messages:
    172
    Likes Received:
    192
    Trophy Points:
    43
    Location:
    Northern Ill-Annoy
    The problem with going to the painless dentist is that just getting an estimate would probably cost as much as I have spent on this tank! But, as it turned out, the dent is immediately above the slot where the petcock fits. And I had a nice German tire iron with a spoon-shaped end. With a bit of careful feeling and taps on the other end of the tire iron, I was able to push on the dent from inside the tank. That took me from this:

    IMG_9736.JPG
    (dent about 1/4" deep)

    to this:

    IMG_9741.JPG
    (two smaller dents about 1/16" deep)

    At this point the dings are well within the realm of what I can fill with a bit of spot filler, something I've done before (though not in a few decades).

    On to the interior... friend brought over his bore scope, so I was able to do a reasonably full inspection. There is surface rust and some stale gas inside. I didn't see any significant scale rust. I think it will need a vinegar soak, but I don't think I need anything stronger or more costly.

    Then there was this thing:

    IMG_9740.JPG

    When I poked the bore scope into the petcock hole, I found a sheet of paper towel in the tank. Well, that could have made a big mess if I hadn't found it; probably would have wrapped around the petcock and kept it from flowing any gas to the engine. It was a pain to fish the thing out with a coat hanger wire, but I got it. Took it to the sidewalk and set it on fire. It burned... slowly. The gas in the tank is really stale, or perhaps somebody tried to rinse the tank with kerosene or something.

    On to other parts of the project: I made a trip to Harbor Freight and picked up a 2800-series case. I think it looks pretty good in place of the passenger seat:
    IMG_9738.JPG

    Right now it's just sitting on top of the flat cross-member at the joint between the plastic front half of the fender and the chrome back half. I think mounting it should be easy--a couple bolts into the cross-member, and a couple plates going to a pair of convenient threaded brackets on the frame behind the shock mounts. Just a bit of fabrication.

    Looking at this, I got an idea, and sorta mocked up the larger HF boxes I'm using as side cases on the Himalayan:

    IMG_9739.JPG

    Hmm... I think this just might work... Supporting the side cases should be pretty easy, requiring no more than a few feet of angle stock, some of which I already have in the garage.

    I suppose at this point i also ought to remove the passenger pegs!
     
  4. Brhatweed

    Brhatweed Well-Known Member

    Messages:
    597
    Likes Received:
    425
    Trophy Points:
    63
    Location:
    Mora MN
    I won't tell anyone if you don't.
     

Share This Page