1. Some members were not receiving emails sent from XJbikes.com. For example: "Forgot your password?" function to reset your password would not send email to some members. I believe this has been resolved now. Please use "Contact Us" form (see page footer link) if you still have email issues. SnoSheriff

    Hello Guest. You have limited privileges and you can't "SEARCH" the forums. Please "Log In" or "Sign Up" for additional functionality. Click HERE to proceed.

What did you do to your Yamaha today?

Discussion in 'XJ Technical Chat' started by Cutlass84, Jun 4, 2007.

  1. Fuller56

    Fuller56 Well-Known Member

    Messages:
    1,121
    Likes Received:
    547
    Trophy Points:
    113
    Location:
    Cary, NC (winter) Harpursville, NY (summer)
    Are there any paintless dent repair guys in your area? Those guys do some amazing work pretty quickly too. They should be able to work that dent out pretty easy, at least to my inexperienced eye. One in the Cary, NC area un-hail damaged my GMC Canyon pick up in a day.
    As far as the rust, WalMart has 30% vinegar in the auto/RV parts area. Grocery store vinegar is, I think, 3%. I have had excellent luck with electrolysis as well. Good Luck!
     
  2. Rayzerman

    Rayzerman Member

    Messages:
    70
    Likes Received:
    31
    Trophy Points:
    18
    Location:
    Ontario Canada
    I use Evaporust to clean tanks with light/medium rust. Water soluable, can reuse if not black (filter it).

    I pulled 3 baseball sized dents out of a tank using a cheap Chinese dent pulling system where you glue on buttons with hot melt then use the provided tool to work them out (start at the edges and work your way in, pull in slow movements). Eventually, you'll have to sand, use filler, prime and paint/clearcoat.
     
  3. ScottFree

    ScottFree Active Member

    Messages:
    174
    Likes Received:
    198
    Trophy Points:
    43
    Location:
    Northern Ill-Annoy
    The problem with going to the painless dentist is that just getting an estimate would probably cost as much as I have spent on this tank! But, as it turned out, the dent is immediately above the slot where the petcock fits. And I had a nice German tire iron with a spoon-shaped end. With a bit of careful feeling and taps on the other end of the tire iron, I was able to push on the dent from inside the tank. That took me from this:

    IMG_9736.JPG
    (dent about 1/4" deep)

    to this:

    IMG_9741.JPG
    (two smaller dents about 1/16" deep)

    At this point the dings are well within the realm of what I can fill with a bit of spot filler, something I've done before (though not in a few decades).

    On to the interior... friend brought over his bore scope, so I was able to do a reasonably full inspection. There is surface rust and some stale gas inside. I didn't see any significant scale rust. I think it will need a vinegar soak, but I don't think I need anything stronger or more costly.

    Then there was this thing:

    IMG_9740.JPG

    When I poked the bore scope into the petcock hole, I found a sheet of paper towel in the tank. Well, that could have made a big mess if I hadn't found it; probably would have wrapped around the petcock and kept it from flowing any gas to the engine. It was a pain to fish the thing out with a coat hanger wire, but I got it. Took it to the sidewalk and set it on fire. It burned... slowly. The gas in the tank is really stale, or perhaps somebody tried to rinse the tank with kerosene or something.

    On to other parts of the project: I made a trip to Harbor Freight and picked up a 2800-series case. I think it looks pretty good in place of the passenger seat:
    IMG_9738.JPG

    Right now it's just sitting on top of the flat cross-member at the joint between the plastic front half of the fender and the chrome back half. I think mounting it should be easy--a couple bolts into the cross-member, and a couple plates going to a pair of convenient threaded brackets on the frame behind the shock mounts. Just a bit of fabrication.

    Looking at this, I got an idea, and sorta mocked up the larger HF boxes I'm using as side cases on the Himalayan:

    IMG_9739.JPG

    Hmm... I think this just might work... Supporting the side cases should be pretty easy, requiring no more than a few feet of angle stock, some of which I already have in the garage.

    I suppose at this point i also ought to remove the passenger pegs!
     
    Fuller56 likes this.
  4. Brhatweed

    Brhatweed Well-Known Member

    Messages:
    598
    Likes Received:
    425
    Trophy Points:
    63
    Location:
    Mora MN
    I won't tell anyone if you don't.
     
  5. ScottFree

    ScottFree Active Member

    Messages:
    174
    Likes Received:
    198
    Trophy Points:
    43
    Location:
    Northern Ill-Annoy
    Busy day today.

    In the morning, I started cleaning the tank. First I made a blanking plate for the petcock, then I sloshed the tank with a couple gallons of hot hot water and dish detergent (Dawn--if it's good enough to get crude oil off birds, it's good enough to remove the last of the stale gas that was in the tank). With that done, I moved on to the "throw in some random hardware and slosh it around" stage. In the interest of domestic tranquility, I did not throw the tank into the dryer to tumble the hardware as many on YouTube suggest :) . I quickly figured out that I could slosh things around pretty well by resting it on my knee and see-sawing it rather than trying to hold it and shake it. So... upright, left side, right side, upside down, repeat, about ten minutes in each position for an hour and a half or so. A whole lot of rust came out; it took about four rinses to get it all. Then I had the problem of getting the hardware out, as you can't just dump it because of the tube in the filler. So I fished them out with a magnet... which worked well for nuts, bolts and screws, but not so well for washers--when they were laying flat in the bottom of the tank, the magnet preferred to stick to the tank wall rather than the washer. I used the shop-vac (with a piece of pipe taped to the nozzle) to remove the last of the water that wouldn't empty out, removed the blanking plate, stuck the shop-vac into the filler (where it fit perfectly), and went inside to have lunch. Half-hour later the inside of the tank was bone dry... and already starting to show some flash rust. I looked around with the borescope and wondered if I really needed to do the vinegar soak.

    But, I decided I might as well at this point, so off to Walmart* for some Serious Vinegar. Not my favorite store, too damn big, hard to find stuff, and if I let the wife know I'm going there's always "a few" other items to pick up. Came back with four gallons of vinegar and a box of cereal. After re-installing the blanking plate (with a Gorilla tape "gasket") and pouring the vinegar (and a bit of water to fill it to the top) into the tank, I found a proper-sized cork in my brewing supplies, corked the tank up and set the tank aside on the bench. Weather forecast says the temperature will be above freezing (and as high as 63º) through Sunday afternoon, which should be enough time for the vinegar to do its thing.

    On to the fun stuff... mounting the "tool box" in place of the passenger seat. The Maxim's frame has a couple threaded tabs welded to the frame, just behind the shock mounts and not used for anything by Yamaha. Which meant they were free for me to use. Only problem was that to reach the tabs, I had to remove the big aluminum grab bar, along with the luggage rack and turn signals.

    I began by getting out the CAD tools to design a bracket that would attach the tool box to the frame bracket:

    IMG_9742.JPG
    "CAD" = Cardboard Aided Design

    After some quality time with the Sawzall, grinder and drill, the cardboard design became steel from my stock of scrap:

    IMG_9744.JPG

    The white squares in the cross member are a lucky find: plastic Chrysler license plate nuts from the local hardware store. They just snap into the rectangular holes in the cross member. Couldn't be easier!

    I initially intended to mount the box directly to the license plate nuts and the steel brackets, but they didn't quite line up with the ovals on the bottom of the box that Harbor Freight obviously intended to be use for bolt holes, so I decided to put a plastic plate in between. I learned a long time ago that a polypropylene cutting board is just perfect for this:

    IMG_9745.JPG
    Yeah, I had to shim things a little. Were these washers fished out of the gas tank? Maybe...

    The four silver dots are where the bolts attaching the box will go... when I make a run to the hardware store for the necessary screws and tee nuts to fasten it down. And put the grab rail, luggage rack, and turn signals back on.

    IMG_9747.JPG
    Worst thing is, I will have to take it all apart next spring to paint the brackets.

    With any luck, I'll have the afternoon free to take it for a ride and see how those springs soak up bumps.
     
  6. Brhatweed

    Brhatweed Well-Known Member

    Messages:
    598
    Likes Received:
    425
    Trophy Points:
    63
    Location:
    Mora MN
    Okay so I talked with my friend about doing some valve jobs and other machine work and right now he's unable to do much of anything, his legs won't allow him to stand for long periods and walking takes a lot of energy. He's over 90 now and doing what he can to keep himself going.
     
  7. Fuller56

    Fuller56 Well-Known Member

    Messages:
    1,121
    Likes Received:
    547
    Trophy Points:
    113
    Location:
    Cary, NC (winter) Harpursville, NY (summer)
    Work on or ride the Seca 650 yesterday? Nope. But I did have it in the truck and hauled it (and the Kawasaki Concours and Honda Shadow, for sale that) to North Carolina for the winter so that I can ride and mess with them all winter.
     
  8. Simmy

    Simmy Well-Known Member

    Messages:
    2,704
    Likes Received:
    1,479
    Trophy Points:
    113
    Location:
    Waterloo Ontario Canada
    What about the Guzzi?
     
  9. Fuller56

    Fuller56 Well-Known Member

    Messages:
    1,121
    Likes Received:
    547
    Trophy Points:
    113
    Location:
    Cary, NC (winter) Harpursville, NY (summer)
    @Simmy, No room this time for Gus. He is tucked in, covered up and on the battery tender with his carbs drained. He is not alone there though. "Lobsta" the Maxim 650 I was gifted in Portsmouth, NH last fall is right next to him and Shoei Seca is STILL waiting for me to finish his rehab. Shoei Seca is a 650 from NJ whose engine was set up solid. He wears a frame mount GF1 fairing and carries a 750 engine now. Almost ready to go, just not quite. Gus will be pleased you asked after him.
     
  10. ScottFree

    ScottFree Active Member

    Messages:
    174
    Likes Received:
    198
    Trophy Points:
    43
    Location:
    Northern Ill-Annoy
    Today I took my increasingly strange Maxim for an 80-or-so mile ride to see how the sprung seat rides, and how many snickers and outright laughs I got.

    IMG_9749.JPG
    It was not towed away while I was enjoying an ice cream cone. Good start...

    I found the seat works very well indeed. It soaks up a bit more of our horrible IL roads. At first I felt I might need to shift the bars back about a half inch, but as the day went by I felt less and less of that. The springs really want the seat pivot to be about a quarter inch further forward (which will require making a new front mounting bracket), and I suspect that if I do that the fit will be just about perfect.

    What did not work well is the gas cap. When I got this bike, it had a horribly corroded cap whose only virtue was that it took the same key as the ignition. I bought a replacement cap on Amazon, and it has rewarded me by anointing my right leg with gasoline when I leave the station after filling up. When I got home, I replaced it with a genuine Yamaha cap I had on the shelf (the one that actually came with this tank, which the previous owner had bought on FB Markeplace after the original tank rusted beyond repair), it seems to clamp down much more solidly and didn't leak a drop when I sloshed the bike violently. So maybe it's fixed... until the gasket hardens, anyway.

    I also did a little foundry work (with a big hammer) on the luggage rack supports, as they keep loosening up and rattling around where the side plates meet the rack. I finally figured out the problem is sloppiness at the Harley factory (this is a Sportster rack/sissy bar assembly donated by a neighbor whose wife no longer rides): the rack is supposed to wrap around the side plates but is a loose fit, so it rocks back and forth and loosens the bolts. A few whacks with a big hammer tightened it up. We'll see if it stays tightened. Either way it gave me a chance to play with my anvil.

    So, my plan for either tomorrow or Saturday (two days of 60º weather left before winter begins here) is to take it for one last long-ish day (hard to ride much beyond 250 miles with the chilly mornings and early sunset, but I won't complain--60s in November is a present). Then I will park it in the back of the garage, drain the gas, and pull the carbs in anticipation of going through them (and doing a bunch of other things to the bike; I have a long list of projects before this thing's a proper sporty touring bike) over the winter.

    Oh, and the 750 tank... continues to pickle. Less scum inside the filler than I expected... so far. Weather and schedule require that I drain the vinegar, rinse and dry and oil-coat the tank no later than Sunday, when it's supposed to be only 45º and rainy all day. I figure I can alternate between the tank and brewing a German Pilsner for January.
     

Share This Page