1. Some members were not receiving emails sent from XJbikes.com. For example: "Forgot your password?" function to reset your password would not send email to some members. I believe this has been resolved now. Please use "Contact Us" form (see page footer link) if you still have email issues. SnoSheriff

    Hello Guest. You have limited privileges and you can't "SEARCH" the forums. Please "Log In" or "Sign Up" for additional functionality. Click HERE to proceed.

Search Results

Search Again
  1. martinfan30
    Thread

    M/C options

    Is there a tried and true master cylinder upgrade out there?
    Thread by: martinfan30, Sep 29, 2008, 4 replies, in forum: XJ Technical Chat
  2. martinfan30
    Thread

    Front brake switch

    Guys I am in need of a front brake switch. While overhauling my M/C, I broke the switch and lost the spring inside the switch. Chacal?
    Thread by: martinfan30, Sep 28, 2008, 4 replies, in forum: XJ Technical Chat
  3. martinfan30
    Thread

    Fork oil capacity

    Anyone know for '83 XJ750 Maxim?
    Thread by: martinfan30, Sep 27, 2008, 13 replies, in forum: XJ Technical Chat
  4. martinfan30
    Thread

    Wheel color

    When I repl my tires, i want to repaint the wheels. What was the stock black? Gloss, med. gloss, low gloss,???
    Thread by: martinfan30, Aug 1, 2008, 2 replies, in forum: XJ Technical Chat
  5. martinfan30
    Thread

    A big thumbs up to all of you who helped.

    As some may remember I have been battling a lean condition in my #3 cyl. FOund the problem after pulling the carbs and disassembling them about...
    Thread by: martinfan30, Jul 13, 2008, 1 replies, in forum: XJ Technical Chat
  6. martinfan30
    Thread

    Lean #3

    Hey fellas, I had recently installed 2 washers to raise the needles as a test. All are almost fully black except #3. I now know I need larger...
    Thread by: martinfan30, Jun 26, 2008, 1 replies, in forum: XJ Technical Chat
  7. martinfan30
    Thread

    Jetting getting closer!

    ok, fellas... Now my 3500-4000 sputtering (lean) is ALMOST gone. My current setup is 122 mains, .065" shims under the needle. 41 pilots 3-31/2...
    Thread by: martinfan30, Jun 19, 2008, 1 replies, in forum: XJ Technical Chat
  8. martinfan30
    Thread

    Adjustable needle

    Hey guys, I have been battling a lean condition for awhile now. I upped the main/pilot to 122/41. No change. Yesterday I added a .030' shim under...
    Thread by: martinfan30, Jun 16, 2008, 1 replies, in forum: XJ Technical Chat
  9. martinfan30
    Thread

    Carb Boots...

    Is there an easier way to put the boots back on the carbs(air box side)after you have reinstalled the carb rack on the intake manifolds? I tear...
    Thread by: martinfan30, Jun 9, 2008, 5 replies, in forum: XJ Technical Chat
  10. martinfan30
    Thread

    Pic Forum?

    Didnt see one so here you go. I may have posted these in the wrong spot earlier. [img] [img] [img]
    Thread by: martinfan30, Jun 6, 2008, 8 replies, in forum: Hangout Lounge
  11. martinfan30
    Thread

    Seafoam

    What is it, and what is its uses?
    Thread by: martinfan30, Jun 4, 2008, 6 replies, in forum: XJ Technical Chat
  12. martinfan30
    Thread

    Store

    How do you find/acess the online store? Rich
    Thread by: martinfan30, May 29, 2008, 2 replies, in forum: Hangout Lounge
  13. martinfan30
    Thread

    Slide drilling

    Is a common practice? What size drill bit? Would I see a benefit? 4300 ft ele. 4 into 1 exhaust. Stock carbs/airbox. I am having an...
    Thread by: martinfan30, May 28, 2008, 8 replies, in forum: XJ Technical Chat
  14. martinfan30
    Thread

    Slight sputtering

    At 60mph, 4k rpm. Throttle set to maintain 60. It runs fine just below, and above that particular throttle setting. I have to keep giving just a...
    Thread by: martinfan30, May 23, 2008, 4 replies, in forum: XJ Technical Chat
  15. martinfan30
    Thread

    RPM's for synching?

    Do I need to hold the rpm's at 14-16 hundred rpm for reading vacuum AND adjusting synch screws? Thanks, Rich
    Thread by: martinfan30, May 14, 2008, 4 replies, in forum: XJ Technical Chat
  16. martinfan30
    Thread

    Throttle shaft seals

    Where can I find them? Thanks again guys, Rich.
    Thread by: martinfan30, May 14, 2008, 5 replies, in forum: XJ Technical Chat
  17. martinfan30
    Thread

    XJ750 Syncing without YICS tool

    Has anyone done this? Will it work? I need to get this bike street ready quickly, and I have a nice guage set... I just wonder if synching...
    Thread by: martinfan30, May 13, 2008, 8 replies, in forum: XJ Technical Chat
  18. martinfan30
    Thread

    Timing chain adjustment

    Can anyone verify for sure which tensioner I have on my 83 xj750? I beleive its auto. I have and read the adjustment for the auto adjuster. If...
    Thread by: martinfan30, May 8, 2008, 3 replies, in forum: XJ Technical Chat
  19. martinfan30
    Thread

    Carb suggestions

    Hey guys, I have pulled the carbs out of my 83 maxim 750. I had a bit of a miss at cruise throttle settings. It sat for nine years. Is the...
    Thread by: martinfan30, May 7, 2008, 2 replies, in forum: XJ Technical Chat
  20. martinfan30
    Thread

    Poor Braking

    Hey guys, my 83 Maxim 750 is a great bike, but the only thing I dont like is the front brakes. They seem really poor braking wise? Any...
    Thread by: martinfan30, May 6, 2008, 2 replies, in forum: XJ Technical Chat
  21. martinfan30
    Thread

    New guy

    Hi, FNG here. I just bought a 83 maxim 750. Love it! 17k miles, been garaged for 9 years. I have a couple questions, it has a bit of a...
    Thread by: martinfan30, May 5, 2008, 2 replies, in forum: XJ Technical Chat
Showing results 1 to 21 of 21
Search Again