Get a set of metric feeler gauges and measure it more accurately. It is easier to do the math and eliminate errors.
Paint remover(or gasket remover) and a plastic scraper will get the old gasket off. use the old clemical stuff not the new environemently frendly...
EBC parts are not junk, they are one of the best in the aftermarket for brake and clutch parts. Buy a set of plates and a NEW set of heavy duty...
I clicked the buy it now button and i could purchase it.
I know you concerns about parts. I have several parts bikes and many bins of spares.
Good compression and not to many miles it should be OK. Why why are you wanting to replace the pistons? I did mine because low compression and...
Most Yamaha fairings and side covers are ABS plastic. ABS glue is easy to get at home centers in the plumbing section. Sheets of ABS are on...
here is one for xs11 79-81 YAMAHA XS1100 1196cc BIGBORE HEAD GASKET 11-VG285HG-1 | eBay for xj11 82 YAMAHA XJ1100 1196cc BIGBORE HEAD GASKET...
Those will work but I don't see a head gasket included in the kit. The 74mm bore requires a special head gasket, the standard wont work.
Preformance was the same. Problem was the piston was not the right size. I had to hone the to get them to fit right and the rings are very...
I an not a fan of overboring to the extreme on XJ11. Thats the biggest you can do it. I did my XS11 with .5mm over size. Yamaha xs1100 XS 1100...
Yes, each master cylinder has its own float switch. either one will set the warning light off. They can be bypassed be plugging the wites together...
The brake indicator warns you of low fluid in the reservoir. It has nothing to do with starting and restarting the engine. You either have a...
Then a dab of silicone grease smeared on the assembly to keep it all together while you drop it in the carb.
PM sent
I hope you have one. I have tried to straighten the butterfly and have gotten it better it still is not 100%. It is much better but I don't think...
The butterfly is different on the UK models, I found dome on EBAY and all of them have different numbers on the valve and the carb body looks...
I have been looking on EBAY, no luck. I will look through the advrider forms also
I am looking for carb parts for a 1993 XJ600 Seca. I need the throttle plate and shaft from the #1 carb, its the one on the far left that has the...
Most of these yamaha side covers are made from ABS plastic. I fixed mine with a sheet of ABS and glue for ABS pipe from the hardware store. It is...
Not normal, that one is damaged beyond repair it will need to be replaced
Did you click on the link at the top right corner of the page and send Len a parts request?
Its the inlet jet for the enrichment(choke) circuit. It needs to be cleaned to allow fuel to flow. the orifice is small, a single strand from a...
I have not got around to it yet. I have all the parts but don't need it yet so its been a project on the back burner. I'll be working on my...
https://www.vintageyamaharally.com/ and on face book https://www.facebook.com/VintageYamahaRally/
Just looked at my kit on amazon and its 235 now Thats a bit pricy
i have a set of accell coils. Only cost 150 for 2 coils and wires. O like them bike runs great. Its been 5 years since i installed them might cost...
Its been a great day dispite the rain. Had to drive to Bryson city because of rain. Had a wonderfull time riding the train through the mountians....
Im leaving next Wednesday . hope to see some XJs there this year. Leaving mine behind because I only have room for 2 this time. XS11 and Venture...
I have always used a impact gun to remove the clutch nut. Torque stick to put it back on. Never had any problems with that.
Any one going to the rally can order a shirt. It will be there when you arrive. https://www.vintageyamaharally.com/shop-1
[IMG][IMG]
Standard auto parts store fuel line will not work well. It is too big to fit around the carbs and it does not take tight bends either. I'm not...
Don't wait too long, rooms are most likley already booked up. There might be a few left. There are always tent camping sites available.
The only cost to you is food and lodging at the Iron Horse. No cost to attend the rally. Its still on as far as I know, I don't know if there are...
I bet your friend did not replace the throttle shaft seal when he had the carbs. Old dry seals are a common issue causing an inconsistant idle...
You will also need to rebuild both petcocks and replace the vacuum daiphram in the "octopuss" fuel lines. PM our parts supplier Chacal he will...
A 1 to 2 second squirt of starter fluid is all that is needed. I light mine with a self igniting propane torch held in my hand. If I get too much...
I use starter fluid all the time to seat beads. Never had any problems even with freshly painted rims. I do take the valve core out , if you don't...
Things that will cause a high idle; Vacuum leak Improper carb sync float levels set too high choke plunger not sealing on one or more carbs idle...
I average 30mpg with mine. A little over 40mpg on the highway. Depending on the traffic conditions I have seen 25 in stop and go
There is more in a service manual than just information on oil types. Its worth investing in one. You will have answers to your questions much faster.
I used the same one as Timbox. Mounted in the saddle bag and wired directly to the battery. Turn it off when not in use .
I have my Vacation time approved and reservation made. Looking forward to another great time. It has never dissapointed me.
Planning to attend the 2020 Vintage Yamaha Rally? ~ September 24-25-26-27, 2020 Now is the time to make your Reservations with the Iron Horse...
A little silicone grease will help "stick" it down while the carb cap is put in place. Typically nothing is needed if the diaphrams are in good...
did not know that for sure. thanks. I have never had a XJ smaller than 750 and that was 30 years ago, all XJ11s now.
So the wheel did turn before you adjusted the brakes? I think you may have the brake adjusted too tight.
20/50 is fine as long as it is not synthetic oil. The starter clutches don't like it, makes them slip.
here in the US we have McMaster Carr industrial supply. They have them for less than 30 $ US https://www.mcmaster.com/standard-taps Im sure there...