I ended up finding out that 4 bolts that held my U-joint to the Middle gear output shaft, I had put new bolts on there and they were maybe 2 cm...
I checked one last night and I would say slightly black, dusty.
Hey guys, been a while. Got the bike back on the road last night for the first time in almost 2 months! Felt pretty good:) My hand seems to be...
Back to fixing some stuff on the bike after the crash now they gave me the go ahead to move my fingers;/ Looked at all the damage and everyting...
Got some good and bad news about this project. Crashed the bike on a turn the first couple days out:/ That's the bad news. Good news is I'm ok...
1. Can do. Does the length matter or just far enough to tuck away? 2. Yes I replaced the chain guide. The large black "plastic" (not sure if it...
Took my first ride around today! Very pleasing feeling after almost 2 years of this rebuild. Couple things I was hoping to see if anyone had...
Good news! No damage (outside of the bolts getting chewed up) Replaced them today and added loctite. Took it out for a little roll around and...
Yea was not happy to find that but at the same time, glad I could find the problem that quickly and have it be that blatant. 2 bolts were off,...
So I think I found out what my problem was [ATTACH] These are 3 of the 4 bolts that connect the u-joint to the engine... F me The 4th is yet to...
As far as I know, yes that is neutral. 1. My N light is on and 2. That is the only time I can roll the bike with it turned off. If I pushed hard...
not sure it that worked and sorry for the shakeyness. hard to film and move the bike. at about 13-20 seconds you can see it catch and shake the...
<iframe src="https://player.vimeo.com/video/176257527" width="640" height="1138" frameborder="0" webkitallowfullscreen mozallowfullscreen...
Got any tips on getting that gator off easily? That thing was a B to get off and on the first time. I will have to take a look at it this week.
Got it out again tonight and messed with the clutch. I actually think the clutch is alright but here is a video of me walking it back to my...
Here were my two questions after being able to ride it around for a bit yesterday. 1. I finally got the bike to idle pretty well on the center...
Excellent, that helps big time.
Ran across this over the weekend [ATTACH] I think it is supposed to go inside the cover for the Clutch, I think it is part 24 in this picture...
Rejetted my carbs and getting the same thing. I even tapped up my pod filters just to see if I "closed" if I could get any sort of change with the...
She f*ucking runs!!!!! Sounds so good. Revs extremely hard but I put individual pod filters on and I believe I need to adjust my jets. I could...
I ended up shooting about 20psi of air into cylinder 2/3 and could feel air coming out the center front of the engine, roughly where the cam chain...
I timed the cams 3 times. The first time I was slightly off. I did it again and was dead on after 10 rotations. But defiantly the first thing I am...
Update Got a new TCI yesterday and all 4 plugs are firing! Problem is still not starting. I got a compression gauge and my readings are as...
Outside of my electrical situation I am dealing with. This is where I am at with the bike:) I know my electrical looks like a mess but I assure...
So tonight I got home and checked a few things which I believe is telling me it is the tci module. I checked the Ohms on the pickup coils from...
I agree, the information I have collected from this site has gotten me quite far with a complete rebuild of my bike. I would of thrown this bike...
The engine hasn't started or isn't running. So hopefully nothing is wrong with the primary coils. But why am I reading 12v at the orange out of...
Yea, removed the caps, same reading. Just completely lost right now. Orange wite reads 12v coming out of the 4 prong connector, gray reads...
On top of that I tested the Primary sides of both coils, I got 3.5ohms on both but the secondary side I can not get a reading on either coil (even...
Sorry I did the earlier post a little backwards... 5a. Switch the Orange and Grey wires from the pickups (6-position TCI plug) at the TCI. If the...
Also when I do have everything wired correctly the Coil that has the gray wire going into it (2 and 3) it starts to heat up when the key is turned...
So I am trying to figure out if my ignition coils are bad or not and was reading this thread....
Update and hoping for some help. Everything above about my Starter, Solenoid, and Switch. All good:) I think It was just me being stupid and not...
I think figured out what was wrong with all my starting system and I am embarrassed to say I believe it was due to my battery not having a full...
I apologize guys. When I said starter, I meant switch:/ My RUN/Kill - Start switch is after market and I was questioning if I had that wired...
Alright, so when I jump the solenoid terminals, the Starter Motor does make a sound. But not I am at a stand still:/ If I am understand this...
I am not an electian but what do you mean jump?:/ I think I know but want to make sure and if so what does that mean for my solenoid?
Electrical update. I don't have the link but I got a diagram from these forms of "Simple Wiring for Xjs" and I have that complete. I have my tail...
I am looking at replacing my Rectifier. Are all of them universal or am I crazy. I have been search a bunch of different sites and when I enter my...
Thanks, That is what I was thinking was going on, but I wanted to make sure incase I was understanding it wrong.
Been working on a lot of things lately but good news, the engine is complete and everything worked out when checking the timing! I will update...
Cases are together and moving on to assembling the rest of the engine. Got another question for you all and a little update on progress. Update....
Hey Chacal. I see position 25 and 27 are repeated. But according to my parts diagram I need bolts for position 24 and 21? Am I missing something?
Hey guys, back for an update. Got the Flu and was down and out for a bit. I ended up doing what K-Moe suggested and just measuring each hole and...
Also 11-17 is listed as 8mm but I think they are 6mm?
Was putting my cases together today and a lot of the bolts I had from the cases don't seem to match up with the numbers from this thread...
Calipers Anyone have an idea how I can un-cease the piston? Or a good way to pull it out. [ATTACH] [ATTACH]
Put everything together and tighten it all down (I only used the 10 bolts that sat around the Crankshaft, not all 39 required for the whole case)...
Today I fit my cases together with my new journal bearings and used the plastigauge to check tolerances. The Manual calls for for 210 in-lb (or...
Excellent! Thanks. Where is that diagram from, I don't seem to have that image in either of the two manuals I have?