Thanks Do the new bars clear the tank at full lock? In the other post "Keep in mind, the turbo MC has the float switch so you will either need...
What bars are on this bike?
What carb mods, if any, are you using with this exhaust?
I have 3 spares... fingers crossed. Unfortunately none look as nice as the one it came with but I'll work on that.
If the seal is compromised will cleaning the breather have a positive effect or only if the seal is not damaged but a clogged breather is causing...
Bummer for me then - is the breather removable? I received another drive today, needs a new coat of paint but otherwise ok. I have another...
So I'm planning on replacing the seal in red but you believe the seal in green is the one that is actually bad. Where I'm seeing oil is the area...
In the drawing above which seal would that be, also does it require breaking apart the pumpkin (which requires special tools)... I have 2 more...
More bearings :) I was trying to avoid removing the swing arm, wonder if it will just come off now with the drive shaft out... For bearing...
Totally understand about it being a kit but darn is that stupid seal a bear to install.
Super, I'll just clean the pan up, the oil level sensor is leaking oil all over the pan, already have the o-ring (as well as the neutral sensor...
I was really surprised at how gummed up my return hole was in my master cylinder - had to take a fine piece of wire (thanks Chacal) and ream out...
Hello all, I have the exhaust off of my 82 XJ650 Maxim, have it sitting on the center stand and some jack stands, wondering if the oil pan can be...
So if the oil is not coming from the engine side of the drive shaft and there is seepage near the final drive, running out (little bit but...
Awesome - thanks! I'll see if I can't document the install process, I'll likely simply cut the old one off...
Dohm sound gernerator :-)
As there is an oil seal between the end of the drive shaft and the final drive it was my thinking there would be oil between the end of the drive...
Made a "removal tool" using a slide hammer and household wire with a single loop over the middle of the end gear... something that would not...
Yeah, my drive shaft apparently needs more than a pretty good tug. I'm just wondering how long before I break something "tugging" on it. Any...
Hello all, I've removed the final drive and need to replace the oil seal on the end of the drive shaft. I'd like to remove the drive shaft...
My valve cover was among the first things to come off, clearly leaking along the front left corner. The oil leak under the engine looks to be a...
What may be happening is the seal at the end of the drive shaft where it goes into the pumpkin may be bad. Now the only problem is getting the U...
Ordered 2 off of ebay. I'll see which one sucks less...
Removed the rear wheel, rear brakes and final drive Removed the front wheel and speedo cable Removed the engine side cover & shift lever Removed...
Hello all, Final drive to shaft tunnel had signs of oil leakage, took off the final drive and confirmed there was oil where the shaft/splines go...
Took off the final drive and a few other bits tonight - oil is in the input shaft at the final drive but not coming from the top oil seal, so...
Thanks - will do!
Going to try to replace the oil level sensor gasket/o-ring and see how that works!
Noticed a drop of oil under my 82 XJ 650 which has not run in months, has the valve cover off awaiting a valve set, carb rebuild, etc. The...
I have a petcock, Yamaha, part number 3AL-24500-00-00, NIB supplied by the previous owner with some other small parts. No good or seek an...
I get the message loud and clear - will take the original petcock from the saddle bag and see how serviceable it is, rebuilt it as needed. Now I...
Thanks - plan to do the valve clearance while I have the extra room to maneuver! For the rear wheel/drive shaft seals reading the manual it looks...
Is it possible to remove the final drive without removing the swing arm or is that required? I'll have the rear wheel off to install new brakes,...
Hello all, My bike came with a non-vacuum replacement petcock. I'm going to remove it prior to repainting the tank - any comments on leaving...
They arrived today. All I can say is: Holy Crap. They look brand freaking new - you really can't tell they are the same carbs that went out. Now...
Working on pictures, went into the garage, then I started taking parts off - still not back together yet but on the way, I'll post some pix to...
After ditching my FZ-09 (most uncomfortable motorcycle ever invented by a mainstream manufacturer) and selling my Speed Triple (to make space in...