Back to the Church of Clean on my carbs! Fully disassembled & ultra sonic cleaned. Found out the enrichment jet in each bowl is super clogged;...
New kit came in, seal was stamped with 15-25-5 so it'll do just fine. [ATTACH] Put motor all back together and on the bike she went, fired...
The only identifiers on this seal are AGO585F 3 T Measuring the seal I got the following - 15-25-4.15...
Thanks Len! Looks like it tore in 2 places which would cause the leak. I'll make sure to measure the new seal that comes in the kit I ordered
Confirmed bad seal at the drive gear... Did I put that seal in backwards? [ATTACH]
Back to tinkering on the bike a little and getting her tuned up for better weather. I've been noticing its been getting harder and harder to crank...
So ended up picking one up and wow they are super light ~2 lbs. XV also required a new reg/rec as the PO stated it was not charging which I...
So another sensor of a non-Atari bike will do?
It does, though I think my oil level sensor is stuck as it's reading 0 ohms so the light stays on. Something to look into next oil change
Hey everyone! Here is my short writeup on installing a new Acewell Speedometer/Tachometer onto my 82' XJ750R. [ATTACH] [ATTACH] New unit...
[ATTACH]
Have a pair of brake line holders that are for the Maxim (I believe), they do not fit the Seca fender. $30 shipped
Yup measurement was done via cold engine :)
Update! Went ahead with the jug replacement and glad I did. Major difference with this set than the previous. Bike starts easier and overall...
Anyone here have experience with Antigravity batteries? I have a 92' XV750 Virago project which should be starting back up soon and was looking...
Picture of broken one for reference [ATTACH]
Looking for a spare camshaft cap, where the valve cover mounts to. Seemed to have over torqued one back when I rebuilt the engine. 82' XJ750R Seca
Ok time for me to ask for help yet again. While my wheels are getting powder coated, today I went over the bike again specifically checking on...
Warmer weather is upon us! Took the bike out a few times and back on the lift for further work. First was oil change and now onto final phases....
Hey guys! Been a while since I've posted but here is a first ride video of this build! She's a little boggy on the low end in 1st gear, my sync...
Try setting menu 3 back to 2. It's actually the number of coils not cylinders as I found in my research. My tac is pretty responsive and with what...
Ok figured it out with some trial and error using resistors. By setting the speedometer fuel sensor setting to "2" on this particular unit and...
Been a while since I've posted but here is a video link to taking her out for a short ride! [MEDIA] Trying to figure out my cheap speedo's gas...
Well, solved my issue getting her tuned in.... Broken spark plug...I have no idea how but during another colortune session cyl No.3 ran a whole...
Yes the XV is a Box O Rocks for sure. Even though its the "newer" gen starter
Been a few days since an update, was waiting on my Colortune and worked on my exhaust...also got a new toy... Bike was pretty loud and I figured...
Spent some major time on the bike today. No signs of a vacuum leak. Used start fluid around the boots, carbs, etc. and no change in RPM's. I...
Noted. Not going that route now since full headlight functionality will be good with a fresh battery
Yup did that (page 5), as it was a early suspicion of mine that they needed to be replaced. I'll check for a leak though with some carb spray.
Confirmed that battery is old/bad and working that out with Chacal. Gave vacuum syncing a shot today and really couldn't get it dialed in....
My headlight has a set of LED DRL's which I will keep on all the time, BUT if I find the battery is just bad a switch may not be needed. Voltage...
Took her out for a spin today! Still need to tune the carbs for smoother throttle. Love the way she sounds! [ATTACH] [ATTACH] Good thing I was...
Chatted with Chacal and after taking apart the cap and cleaning it very very well, I believe the issue is resolved. Tank no longer keeps pressure...
It's brand new from Chacal...should I dig into it?
Shes ready!! Wet sanded, applied compound and polish to tank and plastics! [ATTACH] [ATTACH] Installed the new petcock kit, and gas cap from...
Mail call and paint update!! Got my new battery in from Len along with some other small items. I will get it installed once it's fully charged....
Meant to get an update up last week but here we go! Forks are done! Won't post all the details but will share pics of which parts get replaced in...
More parts from Chacal have arrived and I took a deep dive into my forks today (pun intended). Cleaned every part and found I have one wrong oil...
Well RIP my left front caliper...I had suspicions that it was damaged and probably would not work/be safe on the bike. [ATTACH] Wasn't 100%...
Been doing electrical soldering forever, first time trying it for body repair work. A bit different but it came out nice. I'll add some pics of...
Tank progress is going well! I was able to solder weld all of the visible pin holes and sand back the solder. More showed up once Evapo-rust was...
Alright, so I gave the fork set I got from a member a good cleaning and looked them over. Not leaking and seals look pretty new. Spring bounces...
Chacal does it again! New throttle shaft seals and screws for the butterfly valves (Upgraded to the stainless button head ones). Threw the new...
Mail call from Len (Chacal) from Monday! New airbox boots are in and my my what a difference! So now I have a set of 650 boots to get rid of....
Ok so got it warmed up and performed compression test... Cyl 1 - 105 Cyl 2 - 105 Cyl 3 - 120 Cyl 4 - 105 Not too siked about these numbers since...
Well went ahead and got the wire harness in and hooked everything up to get her to run! She's alive! A bit rough with the airbox not hooked up...
Parts in from Chacal and eBay! Threw on some of those along with new oil filter o-ring, filter and bolt. New engine oil and final drive oil in!...
Is that brake union OEM? It's super clean looking Seems I need to send a message to Galfer when it's time for the lines. Their eBay kit does not...
What did you use for your front brake setup? Specifically referring to the lines and master cylinder. I have my front end to work on soon and...
My final shim came in from Hogfiddles and now all valves are in spec! Closed up the top end with a new valve cover gasket and fresh bolt seals....