Also during the tear down this was on the outside of the bearing closest to the 5th gear. Not sure what it is but seems like an oil seal. Looking...
The edges are kind of flakey. They fell out of place when pulling the housing out during tear down. I’ll have to clean them up more to see if...
Question gentlemen. I want get new Middle gear pinion shims. I have the originals but they rusted. they read .15 and .50. The manual say to...
Ok sounds good. Thanks again
what up guys? I have a question about the connecting rod bolts/nuts when I'm checking clearances for the bearings and journals. I know I have to...
Never ending cleaning [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH]
Will do k-moe
Yea I have to anyway. One of those bad boys shot across the garage never to be seen again lol.
Cleaned the pistons last couple days. [ATTACH][ATTACH][ATTACH]
Thanks for the heads up
Whats up gents. Been MIA for a bit. Too cold out to be cleaning in a unheated garage. Slowly bringing in parts to clean in the house. I didnt...
the upper bolt was so corroded that the head just fell off with minimal force. had to drill it out and gonna re-thread it. other two came out easily
Ive watched Mezzmo's engine overhaul a bunch already. Theyre my go to source when i cant find it in the book.
Yea me and Chacal have been in contact since i got the bike and did the carbs
The tubing you mentioned is barely holding on so ill prob just pull it off. I should prob take closer pictures for you guys to show how crappy it...
Is this just rust build up or was there some sort of gasket around these bolts? It was just falling off while splitting the engine. (Green...
Ok sounds good
I briefly looked over the bearing. No damage so far. On the top of the piston bores there’s a ring of rust maybe a 1/4 from the top. I dunno if a...
Alright got it all apart. Rust was falling from everywhere. But I’m gonna do what u said and clean everything first before i count myself out.
[ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH]
I’ll post more as i go along. Dunno if i screwed or not
Just an update guys. Been slowly disassembling the engine and mannnn it’s pretty bad. Pics below [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH]...
ok got the new meter. Put the rotor on the brushes and stator in. 3 white wires go between 4 and 5 ohms and the brown green are still high at...
yes sir plan on going the whole 9 yards with her. I've only been in the carbs, left crank case, and stator so far and it was pretty bad. I can...
ill def clean all the connectors also and put it all back together to get a more accurate reading
Yea i ordered a better meter. But i did subtract the initial probe to probe reading. Got .5 for the 3 white and .2 for the green/black
I didn’t test the probes to each other. Thanks for the heads up. The manual also says that the temp tested is 68 degrees. It’s colder out now,...
Does it matter if i test the ACG out of the engine? If not i got .8 ohms on the 3 white wires. The brown and green wires read .51 ohms. Haynes...
Yes i have a multimeter. I’ll look up what it should read. Thanks
What’s up guys. Just wondering if the alt/stator is ok or i just need a new one. Some gouges and scrapes, rust, and the wire cover frayed. Back...
Yes i cleaned out the float bowl jet as instructed in one of the write ups. Is there a way to fix the enrichment circuit or can i leave it as is?
Great. I’m assuming I’ll have to replace the whole carb then
Yea i noticed the ding when i loaded the pic. Not sure if they’re all the same length. I’ll measure tomorrow. Was just curious if they’re all...
[ATTACH] [ATTACH] carb #2 pickup tube doesn’t have the small hole at the bottom, or top depending on how your looking at it. I’m new to this and...